PRODUCT
 MOTOR
  Stepping motor
  Hybrid Stepping Motor
  Motion Board/LSI Chip
  Synchronous Motor
  Timer
  DC Motor
  DC Geared Motor
  DC Coreless Motor
  DC Brushless Motor
  Fan Motor
  AC/DC Blower
  Vibration Motor
  Solenoid
  Solenoid Valve
  AC/DC Pump
  AC Motor
  WATER-PROOF Motor
  Servo motor
 ½áº¸¸ðÅÍ°¨¼Ó±â
  MOTOR VARIO
  SIMPO
  NISSEI
  Á¦ÈÞȸ»ç (A to Z)
 ÀϺ»Á¦ÈÞȸ»ç¸®½ºÆ®
  NIHON Bearing
  IKO
  GTR
  FUJI SEIKI
  IMAO Corporation
  KHK
  IWATA MFG
  KONDO SEISAKUSHO
  NBK
  SHOWA DENKI
  MYOTOKU
  SUMITOMO
  ±âŸ¿Ü ´Ù¼ö
¢º ÇöÀçÀ§Ä¡ : HOME > MOTOR > Motion board/chip > PCL6123

PCL6123  (Motion Control Chip - Manual)

Specifications
Number of control axes 2
Reference clock (standard) 19.6608MHz (max 30MHz)
Maximum pulse output frequency 9.8Mpps at 19.6608MHz (15Mpps at 30MHz)
Number of speed setting registers 2 (FL, FH)
Number of steps to set/change the speed 1 to 16,383 (14-bits)
Speed multiplication rate range 0.1 to 600x
Acceleration range 1 to 16,383 (14-bits)
Deceleration rate range 1 to 16,383 (14-bits)
Number of positioning pulses -134,217,728 to +134,217,727 (28-bits)
CPU Interface 8/16-bit bus
Ramping down point 0 to 16,777,215 (24-bits)
Package types 128-pin QFP
Power supply voltage +3.3V ±10%
Additional Specifications
Automatic ramp-down point setting Yes
Ramp-down point offset setting Yes
Up/down counter
(Current position counter)
Yes (28-bits; provided for each axis)
Other counters
(Software zero position auto return)
Yes
External mechanical signal input
(±EL ±SD ORG)
Yes (provided for each axis)
External mechanical start signal for a Hold Start Yes
Output pulse mode CW/CCW, Pulse/Direction, 90°/Ø difference output
Servo motor I/F Yes
Encoder input (up to 4x) Yes (A, B, & Z)
Zero return command with encoder Z phase Yes (provided for each axis)
General-purpose I/O terminal Yes (8 points for each axis)
S-curve acceleration/deceleration control Yes
Specify S-curve range Yes
Triangle operation correction function Yes
One pulse output No
Operation mode selection Yes
Pulser input Yes
Comparator Yes (2 circuits for each axis)
Pre-buffer for next operation Yes (primary)
Next operation auto start control Yes
Simultaneous start/stop Yes
Interrupt status (interrupt cause monitor) Yes
Specify interrupt cause Yes
Stepper motor out-of-order detection Yes
Interpolation operation Yes (linear)
Continuous interpolation operation Yes
Target position override Yes
Operation switch input terminal Yes
Synchronization signal output Yes
Counter hardware latch Yes

  MEANWELL SMPS
   Enclosed Type
   Open Frame Type
   Medical Open Frame
   External Type
   Video Game¿ë
   ATX PC Power¿ë
 DC/DC Converter
   Module Type
   On Board Type
   PCB Type
   Enclosed Type
 DC/AC Inveter
   DC/DC SMPS

  SENSOR & TR
 APM Pressure Sensor
   ATP 100
   ATP 150
   15psi-Dip Type
   1psi-Dip Type
   5.8psi-Dip Type
 JPC PARTS
   DELAY LINES(ACTIVE)
   DELAY LINES(PASSIVE)
   LC & ACTIVE FILTERS
   DC-DC Converter
   LAN PRODUCTS
   PULSE UNITS
Ȩ | ȸ»ç¼Ò°³ | °í°´¹®ÀÇ °Ô½ÃÆÇ | À̸ÞÀÏÁÖ¼Ò ¹«´Ü¼öÁý °ÅºÎ | °ü¸®ÀÚ¸ðµå | °Ô½ÃÆÇ°ü¸®
»ç¾÷ÀÚ µî·Ï¹øÈ£ : 675-87-00071 / ¼­¿ï½Ã ¿µµîÆ÷±¸ ¾çÆòµ¿ 4°¡ 281, ¸£³×»ó½º ÇÑ°­ ºôµù 1017È£
°³ÀÎÁ¤º¸ º¸È£Á¤Ã¥ - À̸ÞÀÏÁÖ¼Ò ¹«´Ü¼öÁý °ÅºÎ [(ÁÖ)Å׶óÆ®·Ð ¸ðµçÀڷḦ µ¿ÀǾøÀÌ ¹«´Üº¹Á¦ ¹× Àç¹èÆ÷¸¦ ±ÝÇÔ´Ï´Ù.]
°í°´»ó´ã ¹× ´ëÇ¥ÀüÈ­ : 02-2068-4301, 4302 / FAX : 02-2068-4308
Copyright (C) 2005 TERATRON Corp. All rights reserved.   E-mail : teratronsale@naver.com